Showing posts with label electrical motor. Show all posts
Showing posts with label electrical motor. Show all posts

Wednesday, November 25, 2020

Electric Motor Protection in Case of Voltage Unbalance and Single Phasing


Voltage Unbalance

When the voltage between all three phases is not equal, the current values in each phase will also become unbalanced. According to NEMA, the maximum voltage unbalance is limited only to 1% both for electric motors and generators. When the voltage unbalance occurs, the current increases gradually in the motor winding which if it continues, the motor will be damaged. Therefore it is necessary derate the motor according to the expected voltage unbalance. 

If in case, the derating is not possible and the voltage unbalance still persists, the loading in this case must be reduced accordingly. This method must be considered to avoid the damage of the equipment.

Causes of Unbalanced Voltage 

  • Connecting unequal single-phase loads. This is why many consulting engineers specify that loading of panelboards be balanced to ± 10% between all three phases.
  • Open delta connections. 
  • Transformer connections open - causing a single-phase condition. 
  • Improper tap settings on transformer banks.  
  • Transformer impedances (Z) of single-phase transformers connected into a “bank” not the same. 
  • The capacitors used in power factor correction capacitors are not the same or some of them are off the line

Insulation Life The effect of voltage unbalance on the insulation life of a typical T-frame motor having Class B insulation, running in a 40°C ambient, loaded to 100%, is as follows:

Note that motors with a service factor of 1.0 do not have as much heat withstand capability as do motors having a service factor of 1.15. Older, larger U-frame motors, because of their ability to dissipate heat, could withstand overload conditions for longer periods of time than the newer, smaller T-frame motors.

Insulation Classes 

The following shows the maximum operating temperatures for different classes of insulation. 
  • Class A Insulation = 105°C 
  • Class B Insulation = 130°C 
  • Class F Insulation = 155°C 
  • Class H Insulation = 180°C

  • Cooper Bussman

Tuesday, November 24, 2020

What are the Basic Factors When Selecting AC Induction Motors?


Cutaway View of Alternating Current Induction Motor

AC induction motors are commonly used in industrial applications. The following motor discussion will center around three-phase, 460 VAC, asynchronous, induction motors. An asynchronous motor is a type of motor where the speed of the rotor is other than the speed of the rotating magnetic field. This type of motor is illustrated. Electromagnetic stator windings are mounted in a housing. 

Power connections, attached to the stator windings, are brought out to be attached to a three-phase power supply. On three-phase, dual-voltage motors nine leads are supplied for power connections. Three power connection leads are shown in the following illustration for simplicity. A rotor is mounted on a shaft and supported by bearings. On self-cooled motors, like the one shown, a fan is mounted on the shaft to force cooling air over the motor.

The nameplate of a motor provides important information necessary when applying a motor to an AC drive. The following drawing illustrates the nameplate of a sample 25 horsepower AC motor.

Nameplate of an AC Induction Motor
Photo: Siemens

Motor Connections

This motor can be used on 230 VAC or 460 VAC systems. A  wiring diagram indicates the proper connection for the input power leads. The low voltage connection is intended for use on 230 VAC with a maximum full load current of 56.8 Amps. The high voltage connection is intended for use on 460 VAC with a maximum full load current of 28.4 Amps.

Motor Speed

Base speed is the nameplate speed, given in RPM, where the motor develops rated horsepower at rated voltage and frequency. It is an indication of how fast the output shaft will turn the connected equipment when fully loaded and proper voltage is applied at 60 hertz. The base speed of this motor is 1750 RPM at 60 Hz. If the connected equipment is operating at less than full load, the output speed will be slightly greater than the base speed.

Service Factor

A motor designed to operate at its nameplate horsepower rating has a service factor of 1.0. Some applications may require a motor to exceed the rated horsepower. In these cases a motor with a service factor of 1.15 can be specified. The service factor is a multiplier that may be applied to the rated power. A 1.15 service factor motor can be operated 15% higher than the motor’s nameplate horsepower. Motors with a service factor of 1.15 are recommended for use with AC drives. It is important to note, however, that even though a motor has a service factor of 1.15 the values for current and horsepower at the 1.0 service factor are used to program a variable speed drive.

Insulation Class

The National Electrical Manufacturers Association (NEMA) has established insulation classes to meet motor temperature requirements found in different operating environments. The four insulation classes are A, B, F, and H. Class F is commonly used. Class A is seldom used. Before a motor is started, its windings are at the temperature of the surrounding air. This is known as ambient temperature. NEMA has standardized on an ambient temperature of 40° C, or 104° F for all motor classes. The temperature rises in the motor as soon as it is started. The combination of ambient temperature and allowed temperature rise equals the maximum winding temperature in a motor. A motor with Class F insulation, for example, has a maximum temperature rise of 105° C. The maximum winding temperature is 145° C (40° ambient plus 105° rise). A margin is allowed for a point at the center of the motor’s windings where the temperature is higher. This is referred to as the motor’s hot spot.

NEMA Design

The National Electrical Manufacturers Association (NEMA) has established standards for motor construction and performance. The nameplate on page 20 is for a motor designed to NEMA B specifications. NEMA B motors are commonly used with AC drives. Any NEMA design (A, B, C, or D) AC motor will work perfectly well with a properly sized variable speed drive. 


AC motor efficiency is expressed as a percentage. It is an indication of how much input electrical energy is converted to output mechanical energy. The nominal efficiency of this motor is 93.0%. 


  • Siemens

Popular Posts

Select Topics